Stamina-products 1300 Manual de usuario

Model#: 15-1300STAMINA PRODUCTSMADE IN CHINAProduct May Vary SlightlyFrom Pictured.2008, 07Exercise can present a healthrisk. Consult a physicianbefo

STEP 7Run the CONNECTION WIRE(25) through the hole in the plate on the HANDLEBAR(5). Attach theHANDLEBAR(5) to the UPRIGHT(4) with BUTTON HEAD BOLT(M8

SET UP INSTRUCTIONS11Place the Magnetic Upright 1300 Bike in the area where it will be used. It is recommended that theMagnetic Upright 1300 Bike be p

OPERATIONAL INSTRUCTIONS12The ADJUSTMENT KNOB(35) should be screwed in tight to make the SEAT POST(6) fit securelyin the MAIN FRAME(1).NOTE:SEAT HEIGH

USING THE METEROpen the Battery Door on the back of the meter.The meter operates with two AA batteries, two batteries included.Refer to the illustrati

14STORAGE1.2.3.4.MAINTENANCEThe safety and integrity designed into the Magnetic Upright 1300 Bike can only be maintained when theMagnetic Upright 1300

15CONDITIONING GUIDELINESHow you begin your exercise program depends on your physical condition. If you have been inactive forseveral years or are sev

16WARM-UP and COOL-DOWNWarm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warmup for two to five minu

17WARRANTYLIMITED WARRANTYMODEL 15-1300Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanshipunder n

PRODUCT PARTS DRAWINGBACKFRONT18

1 Main Frame 1 2 Front Stabilizer 1 3 Rear Stabilizer 1 4 Upright 1 5 Handlebar 1 6 Seat Post 1 7 Crank 1 8 Bearing Housi

TABLE OF CONTENTSMaintenance 14Conditioning Guidelines 15Warm-Up and Cool-Down 16Warranty 17Product Parts Drawing 18Parts List 19Notes 21Fax/Mail Orde

2048 Screw, Round Head (M5 x 0.8 x 15mm) 449 Screw, Round Head (M6 x 1 x 8mm) 250 Nylock Nut (M8 x 1.25) 451 Nylock Nut (M10 x 1.5 x 7mm t

NOTES21

IMPORTANT : Before filling out the form below make sure you have the right information.Refer to the parts list to make sure you're ordering the

3THANK YOU FOR PURCHASING THE1300 Magnetic Upright Exercise BikeTo help you get started, we have pre-assembled most of yourMagnetic Upright 1300 Bike

BEFORE YOU BEGIN4THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Wrench Allen Wrench (6mm)MeterHandlebarUprightRight PedalCrankEndcapFront Stabiliz

5EQUIPMENT WARNING & NOTICE LABELSLabel is larger than actual sizeWARNING LABEL(59)W1This chart is provided to help identify the warning & not

6Part No. and Description Qty40 Carriage Bolt (M8 x 1.25 x 65mm) 441 Bolt, Button Head (M8 x 1.25 x 15mm) 456 Lock Washer (M8) 852 Acorn N

ASSEMBLY INSTRUCTIONS7STEP 1Attach the FRONT STABILIZER(2) to the front of the MAIN FRAME(1) with CARRIAGE BOLTS(M8x1.25x65mm)(40), ARC WASHERS(M8)(55

ASSEMBLY INSTRUCTIONS8STEP 3NOTE:The RIGHT PEDAL(32) has R stamped on the end of the pedal shaft. The RIGHT PEDAL(32) hasright hand threads and is tig

ASSEMBLY INSTRUCTIONSSTEP 5Turn the TENSION KNOB(23) on the UPRIGHT(4) counterclockwise as far as it can go, so the cable endextends out of the metal